Digiplex EVO641R Instrukcja Instalacji Pobierz pdf (Strona 51)

Digiplex -EVO- - 51 - Programming Guide

Installer Function Keys

To access the installer functions, press and hold the [0] key, enter the [INSTALLER CODE], and then:

For LCD keypads: press the key indicated in the list below that corresponds to the function you wish to activate.

For Grafica keypads: press the center action key (Options), highlight the desired function and then press the center action key (Ok).

Automatic Report Code List

Section Description

[4040] Entering this section will reset all programmable sections from [0001] to [3999] to factory default values.

[4041] Entering this section will reset the system master code to 123456.

[4042] Entering this section will reset all Zone programming (including sections [0961] to [0984]) programming to default values.

[4043] Entering this section will reset all access control sections from [2201] to [2712], excluding door labels, to default values.

[4044] Entering this section will reset all user code sections from [1001] to [1999] and [2001] to [2199] to default values.

[4045] Entering this section will reset all dialer (sections [3051] to [3081]), VDMP3 (sections [3087] to [3098]) and control panel (sections [3020] to

[3043], and [3900] to [3991]) programming to default values.

[4046] Entering this section will reset all partition sections from [3101] to [3833], excluding partition labels, to default values.

[4047] Entering this section will reset all PGM (sections from [0901] to [0959]) and all Keyswitch (sections [0501] to [0632]) programming, as well

as all Keyswitch arming/disarming report codes (sections from [0701] to [0832]) to default values.

[4048] Entering this section will clear all user labels, door labels, partition labels, module labels and zone labels from sections [0301] to [0396].

[4049] Entering this section will unlock software reset for sections [4040] to [4048].

[

STAY] Test Report: Sends the “Test Report” report code programmed in section [3902] to the monitoring station.

[

FORCE]

Call WinLoad Software: Will dial the PC telephone number programmed in section [3010] in order to initiate communication with a computer

using the WinLoad software.

[

ARM] Answer WinLoad Software: Will force the control panel to answer a call made by the Monitoring Station that is using the WinLoad software.

[

DISARM] Cancel Communication: Cancels all communication with the WinLoad software or with the Monitoring Station until the next reportable event.

[

MEM]

Installer Test Mode: The installer test mode will allow you to perform walk tests where the bell or siren will squawk to indicate opened zones.

Press the [

MEM] button again to exit. Partitions cannot be armed if the Installer Test Mode is enabled.

[

TRBL] Start Module Scan: The keypad will display the serial number of each module on the combus.

[

ACC] Combus Voltmeter: To verify if the combus is supplying sufficient power, press and hold the [0] key, enter the [INSTALLER CODE] and press the

[

ACC] button. A reading of 12.3V or lower at the panel’s service keypad connector indicates that the voltage is too low. The voltage may drop

during the control panel battery test.

System Event

Default Contact ID Report Code

when using sections [4032] to [4037]

Default SIA Report Code

when using sections [4032] to [4037]

Arming with Master Code (##) 3 4A1 - Close by user CL - Closing Report

Arming with User Code (##) 3 4A1 - Close by user CL - Closing Report

Arming with Keyswitch (##) 3 4A9 - Keyswitch Close CS - Closing Keyswitch

Auto Arming 3 4A3 - Automatic Close CA - Automatic Closing

Arm with PC software 3 4A7 - Remote arm/disarm CQ - Remote Arming

Late To Close 3 452 - Late to Close OT - Late to Close

No Movement 3 452 - Late to Close NA - No Movement Arming

Partial arming 1 456 - Partial Arm CG - Close Area

Quick arming 3 4A8 - Quick arm CL - Closing Report

Remote Arm (voice) 3 4A7 - Remote Arm CQ - Arm with Voice Module

Delinquency Closing 1 654 - System Inactivity CD - System Inactivity

Disarm with Master Code (##) 1 4A1 - Open by user OP - Opening Report

Disarm with User Code (##) 1 4A1 - Open by user OP - Opening Report

Disarm with Keyswitch (##) 1 4A9 - Keyswitch Open OS - Opening Keyswitch

Disarm after alarm with Master Code (##) 1 4A1 - Open by user OP - Opening Report

Disarm after alarm with User Code (##) 1 4A1 - Open by user OP - Opening Report

Disarm after alarm with Keyswitch (##) 1 4A9 - Keyswitch Open OS - Opening Keyswitch

Cancel alarm with Master Code (##) 1 4A6 - Cancel OR - Disarm From Alarm

Cancel alarm with User Code (##) 1 4A6 - Cancel OR - Disarm From Alarm

Cancel alarm with Keyswitch (##) 1 4A6 - Cancel OS - Opening Keyswitch

Auto Arming Cancellation 1 464 - Auto-Arm Time Extended CE - Closing Extend

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Digiplex EVO641R Instrukcja Instalacji Strona 51

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex EVO641R