Digiplex EVO641R Instrukcja Instalacji Strona 3
- Strona / 68
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Digiplex -EVO- - 3 - Programming Guide
Table of Contents
Things You Should Know
About This Programming Guide
This programming guide should be used in conjunction with the EVO Reference & Installation Manual which can be downloaded from our website at
paradox.com. Use this guide to record the settings programmed for this console.
Installer Code (Default: 000000)
The Installer code is used to enter programming mode, which allows you to program all the features, options and commands of the EVO except user codes.
To modify the installer code, refer to section [1000], Installer Code Programming on page 28.
System Master Code (Default: 1234 / 123456)
With the System Master code a user can use any arming method and can program user codes. The System Master code can be 4 or 6 digits in length.
Panel and Codes Reset
To reset the system back to the factory defaults or custom defaults (if they have been programmed), press and hold the Reset button and the Aux button for
4 seconds (See “PCB Layout” on page 65.)
Entering Programming Mode
1) Press and hold the [0] key
2) Enter your [installer code]
3) Enter 4-digit [section] you wish to program
4) Enter required [data]
Decimal and Hexadecimal Programming Table
Certain sections may require the entry of one or more Hexadecimal values from 0 to F.
For LCD keypads:
For Grafica keypads:
Warning or important information. Suggestion or reminder.
Key Value or Action Key Value or Action
[0] to [9] 0 to 9 (Hex & Decimal) [
BYP] E (Hex Only)
[
STAY] A (Hex Only) [MEM] F (Hex Only)
[
FORCE] B (Hex Only) [CLEAR] Exit section without saving (Hex & Decimal)
[
ARM] C (Hex Only) [ENTER] Save current data and advance to next section (Hex Only)
[
DISARM] D (Hex Only)
[0] to [9] = values 0 to 9 respectively Right Action Key (Exit) = Exit section without saving
[#]
= A to F (press the [#] key until the
desired letter appears)
Center Action Key (Save)
= Save current data and advance to next
section
Zone Programming ....................................................... 9
Zone Information ......................................................... 10
Keyswitch Programming ............................................. 19
Programmable Outputs ............................................... 21
User Code Options ...................................................... 29
Arming and Disarming Report Codes ......................... 30
Access Control Sections ............................................. 31
Keypad Numbering ..................................................... 35
Remote Control Programming .................................... 35
Control Panel Settings ................................................ 36
System Options ........................................................... 36
Dialer Options ..............................................................38
Other Options ..............................................................38
Communication Settings ..............................................39
System Event Call Direction ........................................40
VDMP3 Voice Module ..................................................41
Partition Settings ..........................................................42
Special and Trouble Report Codes ..............................48
Other Settings and Modes ...........................................49
Control Panel Hardware Connections .........................55
LCD Keypad Programming ..........................................60
Trouble Display ............................................................68
- Hardware Requirements 2
- Hardware Differences 2
- Table of Contents 3
- Things You Should Know 3
- Entering Programming Mode 3
- Serial Number List 4
- Zone Programming 9
- Zone Information 10
- Zone report codes 15
- Zone Labels 17
- Keyswitch Programming 19
- Programmable Outputs 21
- †: See page 27 25
- † 001 to 064 001 to 064 25
- † Not Used Not Used 25
- Input Speeds 28
- Installer Code Programming 28
- User Code Options 29
- Arming Report Codes 30
- Disarming Report Codes 30
- Access Control Sections 31
- Schedule Programming 32
- SECONDARY SCHEDULES 33
- Backup Schedules 34
- Programming Access Levels 34
- Holiday Programming 34
- Keypad Numbering 35
- Remote Control Programming 35
- Control Panel Settings 36
- System Options 36
- Dialer Options 38
- Other Options 38
- Communication Settings 39
- Reporting Formats 40
- VDMP3 Voice Module 41
- Partition Settings 42
- Partition Timers 43
- Partition Options 1 43
- Partition Panic Alarm Options 45
- Partition Bell Squawk Options 45
- Partition One-Touch Options 45
- Partition Special Options 46
- Special Arming Exit Delay 47
- No Movement Schedule 47
- Other Settings and Modes 49
- Software Reset 50
- Installer Function Keys 51
- Automatic Report Code List 51
- System Event 52
- Default SIA Report Code 52
- Contact ID Report Code List 53
- VDMP3 Installation Diagram 55
- Feature Activation (PGMs) 55
- N 12Hr clock 56
- N Disabled 56
- [018]: Beeping Assignment* 57
- Message Programming 58
- Using the Memory Key 59
- Memory Key (PMC-5) 59
- Combus Voltmeter 59
- BLK and Z1 terminals 60
- BLK and Z2 terminals 60
- Single Zone Inputs 61
- ATZ - Double Zone Inputs 61
- Connections 62
- Telephone Line Connections 63
- Built-in RTC 64
- PCB Layout 65
- Warranty 67
- Limitations of Alarm Systems 67
- Trouble Display 68
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex EVO641R
(32 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji