Digiplex DGP-641 Instrukcja Instalacji Pobierz pdf (Strona 42)

38 Reference & Installation Manual

13 Access Codes

The Digiplex control panel supports 95 user access codes, 1

System Master Code, and 1 Installer Code.

13.1 Installer Code

SECTION [800]

(Default: 000000) The Installer Code is used to enter the control

panel's programming mode, which allows you to program all the

features, options and commands of the control panel and any

modules connected to the combus. The Installer Code can

program the User Code Options and the Partition Assignment,

but cannot program the personal identification numbers. The

Installer Code is six digits in length where each digit can be any

value from 0 to 9.

To change the Installer Code:

1) Press and hold [0].

2) Enter [

INSTALLER CODE].

3) Enter section [800].

4) Enter new 6-digit [

INSTALLER CODE].

13.2 Access Code Length

SECTION [504]: OPTIONS [2] AND [3]

Access codes can be between 1 and 6 digits in length. When

programming access codes with less than 6 digits, press the

[

ENTER] key. When you change the user access code length from 4

digits to 6 digits, the control panel will automatically add the last 2

digits by using the first 2 digits. For example, if your access code is

1234 and you switch to 6 digits the code will become 123412.

When you change the access code length from 6 digits to 4 digits,

the control panel will automatically remove the last 2 digits.

[2] [3] Option

Off Off 4-digit access codes

Off On 6-digit access codes

On Off Same as On/On

On On Flexible access codes

13.3 System Master Code

(Default: 123456) With the System Master Code a user can use

any of the available arming methods with access to all partitions

and can program all user access codes, User Options, Partition

Assignments, and Access Control Options.

Each digit in the System Master Code can be any value from 0 to 9.

The length of the System Master Code is determined by the access

code length feature (see section 13.2). The System Master Code

cannot be set to less than 4 digits in length.

13.3.1 System Master Code Reset

SECTION [950]

To reset the System Master Code to its default (123456):

• Set the RESET jumper to on by placing a jumper on the reset

pins of the control panel

• Use the Installer Code to enter section [950]

Do not remove the power from the control panel.

13.4 Programming Access Codes

Sections [801] to [896]

The instructions that follow detail how to program access codes when

using an LCD keypad. For instructions on how to program users when

using a Grafica keypad, refer to Grafica’s User Manual. A complete

Grafica user manual is available on our website at www.paradox.ca.

In section [801] the installer can program the System Master Code

with an Access Card’s serial number and change the Access Card’s

arming method (see section 13.7 on page 39).

In sections [802] to [896], the Installer Code can program the User

Code Options, Partition Assignment, and Access Control Options,

but cannot program the user code for the System Master Code or

the user access codes. To program the user access codes, refer

the users to the appropriate manual: LCD Keypad System

Manager’s Manual and LED Keypads User Manual. If no partition

assignment is selected, the user access code will only be able to

activate PGMs.

To program user labels, refer to the LCD Keypad System

Manager’s Manual.

Figure 22: Programming User Access Codes

Press & Hold

the [0] key

Enter the

[

INSTALLER CODE]

Enter the

[

SECTION]

User Options

Feature Select

Programming

User Partition

Assignment

Feature Select

Programming

Where Sections [801] to [896] represent user

access codes 01 to 96.

User Options

[1] [2] Feature

off Disabled

on off Master - user can program user

access codes only

on on Full Master - user can program user

access codes, options and

assignments

[3] Duress [6] Stay & Instant

[4] Bypass [7] Force

[5] Arm only[8] off = access keypad’s partitions

only

on = access any partition assigned

to user

*Note: all users can regular arm the system

User Code Partition Assignment

[1] User Code Has Access to Partition 1

[2] User Code Has Access to Partition 2

[3] User Code Has Access to Partition 3

[4] User Code Has Access to Partition 4

Note: The default setting depends on the

programming user’s assigned partitions. For

example, when a user (user with master feature)

that is assigned to partitions 1 and 2 programs a

user code, partitions 1 and 2 will be the default

setting for the new user.

Access Level and Schedule Assignment

First brackets: Access Level

Enter level from 00 to 15 (00 = access to all doors)

Second brackets: Schedule

Enter number from 00 to 15 (00 = all times)

Access Control User Options

[1] Access Card is activated

[2] Can disarm with Access Card

[3] Access Card with Extended Unlocked Period

[4] [5] [6] [7] Feature

on off off off Can Regular arm with Card

on on off off Can Stay arm with Card

on off on off Can Instant arm with Card

on off off on Can Force arm with Card

[8] Can open armed Access Control Doors

Access Level and

Schedule Assignment

Enter digits

Access Control User

Options

Feature Select

Programming

Enter

Access Card

Press the [

ENTER] or [S]

key to save and advance

to the next screen.

Access Card Assignment

Enter Access Card’s serial number or present Card

to the reader

Press the [S] key

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Digiplex DGP-641 Instrukcja Instalacji Strona 42

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex DGP-641