Digiplex DGP-641 Instrukcja Instalacji Pobierz pdf (Strona 31)

DGP-848 Control Panel 27

Section [718]

• WinLoad Access: the panel ended communication with WinLoad

• Installer In: installer has entered the programming mode

• Installer Out: installer has exited the programming mode

8.3 Monitoring Station Phone Number

SECTIONS [561] TO [564]

The Digiplex control panel can dial up to 4 different monitoring station

telephone numbers. Sections [561] to [564] represent monitoring

station telephone numbers 1 to 4 respectively. You can enter any

digit from 0 to 9 and any special-function key (see Table 10, Special

Telephone Number Keys) up to a maximum of 32 digits. Refer to

Event Call Direction in section 8.6 and Reporting Formats in section

8.5 for details on how these telephone numbers are used.

For North American installations using either SIA or

Contact ID reporting formats (see section 8.5), enter *70

and then either P (4-second pause) or W (wait for

second dial tone) before the phone number to disable

call-waiting.

Table 10: Special Telephone Number Keys

8.4 Partition Account #

SECTIONS [551] TO [554]

All report codes are preceded by a 4-digit or 3-digit Partition

Account Number to ensure correct identification of active zones in

a partitioned system. Sections [551] to [554] represent the

Partition Account Codes for partitions 1 through 4. Partition

account numbers can be any hexa-digit from 0 to F.

Example:

If a zone generates an alarm in Partition 1, the control panel will

send Partition Account Number 1 followed by the report code.

Only SIA formats support the “0” digit in its account

numbers. For account numbers that use another

reporting format, you must replace the “0” with an “A”.

To enter an “A”, press the [

STAY] key on LCD keypads

or the [#] key on Grafica keypads. When using the SIA

Format, the control panel will only use Partition

Account Number 1 programmed in section [551], but

the report code will include the partition number.

8.5 Reporting Formats

SECTION [550]

The Digiplex control panel can use a number of different reporting

formats and each of the four Monitoring Station Phone Numbers

(see section 8.3) should be programmed with the same reporting

format unless it is combined with a Pager format. The first digit

entered into section [550] represents the reporting format (see

Table 11, Reporting Formats) used to communicate with Monitoring

Station Telephone Number 1, the second digit represents

Monitoring Station Telephone Number 2 and so forth.

Table 11: Reporting Formats

8.5.1 Standard Pulse Formats

The Digiplex control panel can use the Ademco slow, Silent Knight

fast and Sescoa standard pulse reporting formats (see Table 11,

Reporting Formats).

8.5.2 Ademco Express

The Ademco Express is a high-speed reporting format that

communicates 2-digit (00 to FF) report codes programmed into

sections [600] to [718]. Unlike other Ademco formats, the Ademco

Express does not use the Contact ID Report Codes.

8.5.3 Ademco Contact ID

Ademco Contact ID is a fast communicator format that uses tone

reporting instead of pulse reporting. This communicator format also

uses a pre-defined list of industry standard messages and report

codes that will suit most of your basic installation needs. To

manually program the report codes, key in the 2-digit hexadecimal

values from the Contact ID Report Codes List in the Programming

Guide into the desired report codes in sections [600] to [718] (see

section 8.2 on page 25). You can also enter 00 to disable reporting

or FF to use the default report code from the Automatic Report

Code List in the Programming Guide. To automatically program a

set of default Contact ID codes, refer to section 8.13 on page 28.

8.5.4 SIA FSK

SIA FSK is a fast communicator format that uses tone reporting

instead of pulse reporting. This communicator format uses a pre-

defined list of industry standard messages and report codes that

will suit most of your basic installation needs. To manually program

the report codes, enter 00 to disable reporting or any other value to

use the default report code from the Automatic Report Code List in

the Programming Guide. To automatically program a set of default

SIA FSK codes, refer to section 8.13 on page 28.

8.5.5 Pager Reporting Format

Using this format allows the control panel to transmit report codes to

a pager. A pound symbol “#” is automatically generated after the

report code. Please refer to Pager Delay in section 8.12 on page 28.

8.6 Event Call Direction

SECTIONS [522] TO [536]

As shown in Figure 20 on page 24, the control panel events are

divided into three event groups for each partition and two global

event groups. Each event group can be programmed to dial up to

four monitoring station telephone numbers and to use one of the

four telephone numbers as a backup. The numbers are dialed

sequentially starting from 1, skipping any disabled numbers and

stopping once all selected telephone numbers have been reached.

Function LCD Grafica

[STAY]

[#]

(press key until

desired letter/symbol

appears)

FORCE]

Switch to Tone Dialing (T) [

ARM]

Wait for second dial tone (W) [DISARM]

4-second pause (P) [

BYP]

Clear [

CLEAR] Left action key (Clear)

Delete [TRBL]—

Delete from cursor to the end [

ACC]—

Insert space [

MEM]—

0 = Ademco slow (1400Hz, 1900Hz, 10BPS)

1 = Silent Knight fast (1400Hz, 1900Hz, 20BPS)

2 = Sescoa (2300Hz, 1800Hz, 20BPS)

3 = Ademco Express (DTMF 4+2)

4 = Reserved for future use

5 = Ademco Contact ID

6 = SIA FSK

7 = Pager

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Digiplex DGP-641 Instrukcja Instalacji Strona 31

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex DGP-641