Digiplex DGP-641 Instrukcja Instalacji Pobierz pdf (Strona 40)

36 Reference & Installation Manual

12.4 Installer Code Lock

SECTION [990]

Enter 147 into section [990] to lock all programming. When 147 is

programmed in section [990], performing a hardware reset as

described in section 12.1 on page 35 will not affect the current

panel settings. To remove the Installer Lock, enter 000 into section

[990]. (Default: Unlocked)

12.5 Partitioning

SECTION [500]: OPTIONS [1] TO [4]

The Digiplex control panel can provide your system with up to four

completely independent partitions. Most features and options in the

Digiplex System can be independently set for each partition such

as Event Reporting, Entry/Exit Delay, Bell Squawk, One-Touch

arming, Panic Alarms and many more. All zones, keyswitch zones,

user codes and system modules are assigned to specific partitions,

making this a true partitioned system. In section [500], enable the

option(s) that correspond to the desired partition(s). Where options

[1] to [4] represent partitions 1 through 4.

12.5.1 Panel Partition Assignment

SECTION [440]

The control panel will report system events as originating from the

partitions enabled in this section. The System Troubles (i.e. AC

Failure, TLM Failure, etc.) can only be viewed through the

partitions enabled in this section.

00 = All enabled partitions (see section [500])

01 = Control panel installed in Partition 1

02 = Control panel installed in Partition 2

03 = Control panel installed in Partition 3

04 = Control panel installed in Partition 4

12.6 Installer Function Keys

To access the installer functions, press and hold the [0] key, enter

the [INSTALLER CODE], and then...

For LCD keypads: press the key indicated in the list below that

corresponds to the function you wish to activate.

For Grafica keypads: press the center action key (Options),

highlight the desired function and then press the center action key

(Ok).

Test Report: [STAY]

Sends the Test Report report code programmed in section [717] to

the monitoring station.

Call WinLoad: [FORCE]

Will dial the PC telephone number programmed in section [560] to

communicate with a computer using WinLoad.

Answer WinLoad: [ARM]

Will force the control panel to answer a call made by the monitoring

station that is using WinLoad.

Cancel Communication: [DISARM]

Pressing this function key cancels all communication with the

monitoring station or WinLoad until the next reportable event.

Installer Test Mode: [MEM]

The Installer Test Mode will allow you to perform walk tests where

the bell or siren will squawk to indicate opened zones. Press [MEM]

again to exit. Partitions cannot be armed if the Installer Test Mode

is enabled.

Module Scan: [TRBL]

This feature instructs the control panel to verify the status of the

modules connected to the combus. The control panel will fix any

problems with the internal organization of the modules in the

control panel. The keypads will display the serial number of each

module that has been connected to the combus.

Combus Voltmeter: [ACC]

LCD keypads (DGP2-641BL) only.

To verify if the combus is supplying sufficient power, press and hold

the [0] key, enter the [

INSTALLER CODE] and press the [ACC] key on

the LCD keypad. A reading of 9.2V indicates that the voltage is too

low. The voltage may drop during the control panel battery test (see

section 2.4.1 on page 2).

12.7 System Date & Time

SECTION [502]: OPTION [6]

The System Date and Time is programmed through the User

Menu, please refer to Clock Loss in section 16.7 on page 47.

12.7.1 Daylight Savings Time

By enabling option [6] in section [502], the control panel will

automatically adjust the system's clock (time) for daylight saving

changes. At 2:00AM on the first Sunday of a full weekend in April,

the control panel will add one hour to the programmed time (clock).

At 2:00AM on the last Sunday of a full weekend in October, the

control panel will subtract one hour from the programmed time

(clock).

12.8 Shabbat Feature

SECTION [522]: OPTION [4]

With option [4] on, all addressable detection devices and keypads

in the system will no longer display any system status through the

LCD and/or LEDs between noon (12:00PM) Friday and midnight

(12:00AM) Saturday. Therefore, normal operation will be re-

instated Sunday morning at 12:00:01AM.

During the Shabbat period:

• the LCD keypads only display the date and time

• the backlight is disabled

• the LED indicators on all addressable detection devices and

keypads in the system are disabled

If required, a user can access all the usual commands and features

during the Shabbat period by pressing a key or, if Confidential

Mode is enabled in the keypad, by entering their access code.

When no actions have occurred for two minutes, the Shabbat

Feature will re-activate.

12.9 Module Reset

SECTION [951]

To reset a module that is connected to the combus to its default

values, key in the module's serial number into section [951].

12.10 Locate Module

SECTION [952]

If you wish to locate a specific module (e.g. detector, zone

expansion module, etc.) connected to the combus, key in the

module's serial number into section [952]. The green

LOCATE LED

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Digiplex DGP-641 Instrukcja Instalacji Strona 40

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex DGP-641