Digiplex DGP-641 Instrukcja Instalacji Pobierz pdf (Strona 30)

26 Reference & Installation Manual

Section [680]

• Auto Zone Shutdown: a zone communicates more than the

programmed number of transmissions in a single armed

period (see section 4.4.1 on page 13)

• Duress: a Duress enabled access code is keyed in (see

section 13.5.2 on page 39).

8.2.8 Zone Tamper Report Codes

SECTION [681] TO [692]

A report code can be programmed for each of the 48 available

zones. Whenever a tamper or wire fault occurs on a zone, the

control panel can send the appropriate report code to the

monitoring station identifying which zone was tampered. If the

Tamper Recognition Options (see section 7.4 on page 22) are

disabled, the control panel will not report the occurrence of any

tampers or wire faults.

8.2.9 Zone Tamper Restore Codes

SECTIONS [693] TO [704]

A report code can be programmed for each of the 48 available

zones. Whenever a tampered zone is restored, the control panel

can send the appropriate report code to the monitoring station

identifying which zone has been restored.

8.2.10 Special Tamper Report Codes

SECTION [705]

• Keypad Lockout: (see section 6.10 on page 20)

8.2.11 System Trouble Codes

SECTIONS [706] TO [711]

Section [706]

• AC Failure: no AC input detected on the control panel. The

control panel can delay reporting this event, please refer to

Power Fail Report Delay in section 8.9 on page 28.

• Battery Failure: the back up battery is disconnected or the

battery voltage is less than or equal to 10.5V

• Auxiliary Supply: the auxiliary power supply’s current is greater

than or equal to 1.1A.

Section [707]

• Bell Output: the bell/siren output is disconnected or the current

is greater than or equal to 3A

• Clock Loss: the control panel detects a loss in panel time (see

section 12.7 on page 36)

• Fire Loop Trouble: a tamper has been detected on a fire zone

(see section 4.2 on page 12)

•N/A

Section [708]

• Combus Fault: a module has been removed from the combus.

• Module Tamper: a tamper or wire fault is detected on a module

other than a motion detector connected to the combus

• ROM Check Error: problem with on-board Read-Only Memory

• Module TLM: TLM failure detected on voice dialer connected

to the combus

Section [709]

• Module Fail to Communicate: a module has failed to

communicate with the monitoring station

• Printer Fault: the Printer Module connected to the combus has

detected an error (see the Printer Module Manual for details).

• Module AC Failure: no AC power detected on a module

connected to the combus

• Module Battery Failure: the backup battery on a module is

disconnected or the battery voltage is low

Section [710]

• Module Auxiliary Failure: the auxiliary output of a module

connected to the combus has exceeded current limits

• Wireless Transmitter Low Battery

• Wireless Module Supervision Failure: This report code is

global unless using the Contact ID or SIA reporting formats.

Section [711]

• Phone Number 1 Fail to Communicate

• Phone Number 2 Fail to Communicate

• Phone Number 3 Fail to Communicate

• Phone Number 4 Fail to Communicate

Please note: there is no Fail to Communicate for Pager

telephone numbers.

8.2.12 System Trouble Restore Codes

SECTION [712] TO [716]

Section [712]

• TLM: a TLM failure has restored.

If the Telephone Line Monitoring (see section 9.1 on

page 29) is disabled, the control panel will not transmit

the TLM report code.

• AC Failure Restored

• Battery Failure Restored

• Auxiliary Supply Restored

Section [713]

• Bell Output Restored

• Time programmed

• Fire Loop Trouble Restored

•N/A

Section [714]

• Combus Fault Restored

• Module Tamper Restored

• ROM Check Error Restored

• Module TLM Restored

Section [715]

•N/A

• Printer Fault Restored

• Module AC Failure Restored

• Module Battery Failure Restored

Section [716]

• Module Auxiliary Failure Restored

• Wireless Transmitter Low Battery Restored

• Wireless Module Supervision Restored: This report code is

global unless using the Contact ID or SIA Reporting formats.

8.2.13 Special Reporting Codes

SECTION [717] AND [718]

Whenever the system generates one of the following instances, the

control panel can send the appropriate report code to the

monitoring station identifying the type of system occurrence:

Section [717]

• Cold Start: the control panel was completely shutdown (total

power loss) and the control panel was re-started

• Warm Start: the control panel performs a reset due to any

sudden problem other than power loss

• Test Report: report generated automatically (see section 8.8

on page 28)

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Digiplex DGP-641 Instrukcja Instalacji Strona 30

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digiplex DGP-641